0

Hose Ends

Is fuel seeping at the joint, or do you need to connect a new hose to a pump or filter? The hose ends here connect PTFE and braided hoses to the rest of the system and are for you if you are building a fuel, oil or cooling circuit in your project.

What does a hose end do?

The hose end is clamped onto the hose and provides a threaded connection, typically in AN size, that can be screwed onto fittings at the pump, filter, cooler or fuel rail. The swivel nut lets you turn the hose into position without twisting it. For permanent fitting with a crimping tool, you will find crimp hose ends in the subcategory.

How to choose a hose end

  • Hose type: A hose end for PTFE hoses typically has an olive insert that clamps around the inner liner and normally does not fit rubber-based braided hoses. DeatschWerks, for example, offers both PTFE and CPE versions.
  • Size: The AN size, e.g. 6AN or 8AN, must match both the hose and the connection. Which size you need depends on flow, fluid and power target.
  • Angle: Straight, 45 or 90 degrees. Choose based on space and hose routing so the hose does not kink or rest against hot parts.
  • Application: Some hose ends are designed for a specific system, e.g. Russell EFI hose ends.

Installation and maintenance

Cut the hose straight and clean, and follow the manufacturer's instructions – PTFE hose ends typically require a new olive if the joint is taken apart. Tighten to the recommended torque, and pressure-test the system before starting the engine. Inspect the joints regularly for moisture and loose nuts, especially near the exhaust manifold and turbo. Other brands in the category include Fragola, Vibrant and GReddy.

Frequently asked questions

Can I use the same hose end for PTFE hose and braided rubber hose?

Typically not. PTFE hose ends seal with an olive against the hard inner liner, while hose ends for rubber-based hoses grip the hose differently. Always check that the hose end is designed for your specific hose type.

Can a PTFE hose end be reused?

The body and nut can often be reused, but the olive insert deforms during installation and should typically be replaced when the joint is taken apart. Follow the manufacturer's instructions for the specific product.

What is the difference between a crimp hose end and a reusable screw-on hose end?

A crimp hose end is pressed on with a special tool and cannot be taken apart again. A screw-on hose end can be fitted with ordinary tools and can often be disassembled. The choice depends on your tools and whether you want to be able to change the hose routing later.

View as Grid List
Sort by
Display per page

HOSE END

rad14-0635
Radium Engineering -8AN 45 Degree PTFE Hose End - Black
8,23 € excl. VAT

HOSE END

rad14-0632
Radium Engineering -6AN 45 Degree PTFE Hose End - Black
8,21 € excl. VAT

HOSE END

rad14-0633
Radium Engineering -6AN 90 Degree PTFE Hose End - Black
8,21 € excl. VAT

HOSE END

rad14-0634
Radium Engineering -8AN Straight PTFE Hose End - Black
4,97 € excl. VAT

HOSE END

rad14-0636
Radium Engineering -8AN 90 Degree PTFE Hose End - Black
8,21 € excl. VAT

Lines & Fittings

dwk6-02-0856
DeatschWerks 8AN Female Swivel 90-Degree Hose End PTFE (Incl. 1 Olive Insert)
12,76 € excl. VAT

Lines & Fittings

dwk6-02-0850
DeatschWerks 6AN Female Swivel Straight Hose End PTFE (Incl. 1 Olive Insert)
6,46 € excl. VAT

Lines & Fittings

dwk6-02-0805
DeatschWerks 8AN Female Swivel Straight Hose End CPE
5,52 € excl. VAT

Lines & Fittings

dwk6-02-0807
DeatschWerks 8AN Female Swivel 90-Degree Hose End CPE
10,24 € excl. VAT

Lines & Fittings

dwk6-02-0803
DeatschWerks 6AN Female Swivel 90-Degree Hose End CPE
9,61 € excl. VAT

Lines & Fittings

dwk6-02-0801
DeatschWerks 6AN Female Swivel Straight Hose End CPE
5,20 € excl. VAT

Lines & Fittings

dwk6-02-0802
DeatschWerks 6AN Female Swivel 45-Degree Hose End CPE
9,60 € excl. VAT

Lines & Fittings

dwk6-02-0852
DeatschWerks 6AN Female Swivel 90-Degree Hose End PTFE (Incl. 1 Olive Insert)
11,80 € excl. VAT

NONEXTRUDEDALFITTING

vib21216
Vibrant -16AN 120 Degree Elbow Hose End Fitting
17,81 € excl. VAT

NONEXTRUDEDALFITTING

vib21910
Vibrant -10AN 90 Degree Elbow Hose End Fitting
11,01 € excl. VAT

NONEXTRUDEDALFITTING

vib21506
Vibrant -6AN 150 Degree Elbow Hose End Fitting
10,97 € excl. VAT

NONEXTRUDEDALFITTING

vib21206
Vibrant -6AN 120 Degree Elbow Hose End Fitting
10,96 € excl. VAT

NONEXTRUDEDALFITTING

vib21406
Vibrant -6AN 45 Degree Elbow Hose End Fitting
9,25 € excl. VAT

NONEXTRUDEDALFITTING

vib21504
Vibrant -4AN 150 Degree Elbow Hose End Fitting
10,04 € excl. VAT

NONEXTRUDEDALFITTING

vib21012
Vibrant -12AN Straight Hose End Fitting
8,55 € excl. VAT

NONEXTRUDEDALFITTING

vib28304
Vibrant -4AN 30 Degree Hose End Fitting for PTFE Lined Hose
11,62 € excl. VAT

NONEXTRUDEDALFITTING

vib29984
Vibrant -4AN Forged Aluminum Non Swivel Hose End for PTFE Lined Hose
12,46 € excl. VAT

NONEXTRUDEDALFITTING

vib21220
Vibrant -20AN 120 Degree Elbow Hose End Fitting
27,53 € excl. VAT

NONEXTRUDEDALFITTING

vib21420
Vibrant -20AN 45 Degree Elbow Hose End Fitting
25,75 € excl. VAT